(Your shopping cart is empty)
Search 




You are here: Home > Care Products
The single most important tip that we cannot emphasize enough is the simple maintenance that is required to ensure a long, trouble-free life for your Enforcer boat and Zenoah engine. Though maintenance for these boats are very minimal, we have found that certain care products and procedures are recommended over others.

Pre-mix oil - We recommend the use of AMSOil 100-1 two-cycle pre-mix oil at a ratio of 32-1. This works out to four ounces per one gallon of gasoline. Though the engine manufacturer recommends a leaner ratio, we have found over many years of testing and sales that this particular brand and mix ratio is superior in performance and reduced part wear.

Drive Shaft Lubrication - Any brand of wheel packing or marine grease is sufficient to lubricate the cable drive system. We recommend the use of a small hand held grease gun available through Warehouse Hobbies or other automotive outlets. These guns use small grease cartridges that are available at most automotive or automotive sections of department stores. Enforcer prepared Zenoah engines are equipped with a Zerk fitting so lubrication can be done in this manner.

Radio Box Tape - Warehouse Hobbies markets a specific clear vinyl one inch tape to seal Enforcer radio boxes. This tape leaves very little residue when removed. Electrical tape is permeable, but is more difficult to seal due to its black color in nature and tends to leave a greater amount of residue when removed. Cleaning - Enforcer boats can be cleaned inside and out with a mild grease cutting water-soluble detergent and warm water. The exterior of the boat can be waxed using any product that is safe for fiberglass gel-coat finishes.

Salt Water - Enforcer boats can be operated in salt water but require additional maintenance procedures immediately after use. Follow all directions that are included with your boat to perform proper maintenance.
Sort By:
Page of 1  
Enforcer Drive Cable Grease Injector Conversion
Our Price: $4.95

We are now offering this easy to use cable greasing system designed to work with all Enforcer factory Ready to run boats or Enforcer Zenoah engines with 3-point mounting system.
It is so easy to use and inserts the correct amount of shaft grease in seconds.
EPO Grease
Our Price: $4.59

Use this grease on drive shafts as well as bearing applications. Unlike other liquid or paste grease, EPO is jelly-like, making it a great universal lubricant.
EPO Grease (9oz.)
Our Price: $8.95

Use this grease on drive shafts as well as bearing applications. Unlike other liquid or paste grease, EPO is jelly-like, making it a great universal lubricant.
Amsoil Premix (1 Quart)
Our Price: $12.95

NEW! Large 1-Quart. Now twice the oil for 1/2 the price.
Our favorite pre-mix lubricant because it does the job! By mixing it at 32:1 (4 oz. per gal.) for stock engines and 25:1 (6 oz. per gallon), it allows plenty of oil to remain in the crankcase, keeping needle bearings lubed and cool making risk of bearing related engine failure a minimum. Its synthetic blend permits richer usage with little or no carbon build-up!
Amsoil MP
Our Price: $7.95

Amsoil metal protector comes in an 8-ounce pressurized spray can like many other light weight lubricants, but it has a little extra something that makes it different. The special formula leaves a protective film that retards rust and corrosion. It is safe for use on plastics, will not gum up, and is perfect as an after-run protectant.
Electronics Lubricant
Our Price: $11.95

A fine product designed for electronic use but safe on plastic! Lubricates and protects your electronics from moisture. It virtually eliminates corrosion and oxidation. We’ve found it works great for spraying directly inside servos and receivers that have gotten wet. A must for any model boater.
Electronic Cleaner
Our Price: $9.95

This new formula is specially developed for cleaning electronics and displacing moisture. It’s safe for use in direct contact with plastic. An absolute must for your tool box and a radio savior if your components get wet or submerged.