|
|
|
|
|
|
Power Rod Receiver Switch
|
Our Price: $14.95
|
|
|
New Innovation from Enforcer! The Power Rod Receiver Switch. Universal mount, waterproof switch that replaces those trouble causing slide switches. The PR is so easy to install, simply drill one half inch hole in your radio box, or through a bulkhead if used on a scale model to mount the body of the switch. The machined aluminum cap contains a super powerful mini-neodymium magnet which when screwed on to the switch body activates an internal incapsulated reed switch. To turn the system off, simply unscrew the cap. The cap comes with a small swivel tether wire that can be attached inside the hull to a rail so the cap is always there when you need it. Designed by Tony Castronovo.
|
|
|
|
|
|
|
|
|
|
|
|
|
Enforcer Magna-Pro Balancer
|
|
Our Price: $29.95
|
|
|
The Pro-Balancer features high grade extremely high power neodymium magnets that will support each shaft end seperatly making contact with only one end at a time, so precision balancing can be done. This design enables you to move the prop and shaft assembly from one side to the other so you can see any run out from either side of the prop hub. This design is unlike any other balancer of its kind.
|
|
|
|
|
|
|
|
|
|
|
|
|
Prop Bullet
|
|
Our Price: $5.95
|
|
|
Precision CNC Stainless Steel Prop Nut. Replace that ugly lock nut with our new "Bullet" Prop Nut. Features a back nut that threads onto the prop shaft first followed by the Bullet. Once tightened against the prop the backnut and prop Bullet are friction locked together. No set screws to damage threads or the mess of thread lock.
(1) Bullet nut and (1) back nut per set.
|
|
|
|
|
|
|
|
|
|
|
|
|
Functional Engine Scoops (Pr.)
|
|
Our Price: $24.95
|
|
|
So you like the scoops on the back of our new 57 Old School...
You didn't think we would make you buy the boat to get them...
We are offeing a pair (2) of these lightweight hand-laid fiberglass scoops so you can install them on your hatch cover and be as cool as us. We mean literally...These scoops really work. Simply mount them and cut out the openings and you will have a set of functioning scoops that will look great and take the place of unsightly holes to let air inside the hull.
|
|
|
|
|
|
|
|
|
|
|
|
|
Machined Nylon Spacers (4)
|
|
Our Price: $3.95
|
|
|
Use these nylon spacers as needed to shim rail spacing between engine mounts. CNC machined nylon, 1 inch OD x 1/16 inch thickness. Can be used individually or stacked as needed between engine mount and stringer rail, eliminating the potential pressure exerted on rails that are pulled inward when tightened. Sold 4 to a bag.
|
|
|
|
|
|
|
|
|
|
|
|
|
Enforcer EKG (Engine Kill Guard)
|
|
Our Price: $39.95
|
|
|
The EKG “Engine Kill Guard” is a new product designed by; Frank Ackinno and Tony Castronovo of Warehouse Hobbies Inc
prompted by a overseas customer to produce a device that is actually mandated in Europe, that will shut a gasoline ignition down in the event of low radio (receiver) batteries or worse a complete loss of power.
|
|
|
|
|
|
|
|
|
|
|
|
|
Overkill Temp Guard
|
|
Our Price: $29.95
|
|
|
New! from Enforcer Mfg Co.
Easy to install device attaches to your Zenoah water jacket as shown. Connect the black coil tap wire to one terminal and the second terminal to the engine block. Designed to stall the engine if water jacket temperature exceeds 180 degrees F.
|
|
|
|
|
|
|
|
|
|
|
|
|
Piston Stop Tool
|
|
Our Price: $10.95
|
|
|
CNC aluminum quality construction designed to fit 10mm spark plug holes used on Zenoah, CY, and similar clone engines. We designed this tool to lock the piston just after "bottom dead center" at the strongest point so less load is placed on the piston rod. Simply screw it in the spark plug hole and it will lock the crank shaft so you can install or remove; clutches, collets, and flywheel. Non-slip knurled handle, a must for all workshops and tool boxes.
|
|
|
|
|
|
|
|
|
|
|
|
|
Enforcer Z5
|
|
Our Price: $29.95
|
|
|
At Warehouse Hobbies Inc. / Enforcer Mfg. Co. it is not unusual to hand assemble a dozen or more engines a day. Tony C. of Warehouse Hobbies designed a single tool that makes engine assembly easier, and less tools on our production line. The original tool has been used for the last four years in our factory, and now he has refined this tool for production and consumer use.
|
|
|
|
|
|
|
|
|
|
|
|
|
Machined Kill Switch
|
|
Our Price: $12.95
|
|
|
Push button kill switch works with Zenoah and Homelite Engines. Also Installs on our Easy Start handle, EZ85.
|
|
|
|
|
|
|
